Solvent based Wet Look Sealer & Joint Sand Hardener (VOC Compliant)
(We do ship orders from our local distributor.)
TAMTECHseal Wet Look Sealer SB-VOC is designed to provide a wet look for pavers, concrete, stamped concrete and exposed aggregate. It will seal and protect these surfaces while enhancing the beauty. This solvent-based methacrylate polymer is UV stable and forms a tremendous bond to the substrate. It can also stabilize and harden the sand in paver joints. TAMTECHseal is available in clear and 25 different colors. The product also resists weather, water intrusion, freeze thaw damage and staining. The treated surface will be easier to clean. The sealer is breathable, thus moisture is not trapped in the substrate. It is an exterior product that can be used on new or existing applications.
We do ship orders from our local distributor. Please call 800-277-3207 or e-mail [email protected] for a quote.
PRODUCT FEATURES:
- Wet look
- Stabilizes sand in paver joints
- VOC Compliant
- Available in clear & 25 colors
- Resists water, surface staining
- UV Stable
- Resists freeze-thaw damage
- Breathable
- Exterior applications
INSTRUCTIONS:
Surface must be clean and dry. Remove all dirt, paint, efflorescence, grease, oil and loose debris. A pressure washer is recommended on older or dirty surfaces to remove the dirt and debris. Use a concrete degreaser for removing oil and grease spots. If water is used, allow a day to dry before sealing. Use protective coverings to protect nearby plants, grass, shrubs, plastic, asphalt and painted surfaces. For paver applications, be sure sand is filled in joints to the required level slightly below the top of the pavers. Completely remove all remaining sand from the top of the pavers. Do not thin product. Apply product with a pump-up sprayer, roller, brush or use low pressure spray equipment, about 10 -15 psi with a fan type spray nozzle. For roller applications, use a short nap roller for smooth surfaces, a medium nap roller for textured surfaces and a long nap roller for exposed aggregate. Keep roller wet on every stroke. Then cross roll without re-dipping every few feet. Let dry. If necessary on more porous surfaces or to increase the wet look, apply a second coat. Do not leave excess or pooled material on the surface. Product will dry to the touch in typically 45-60 minutes at 74 degrees F. Keep foot traffic off for 4-6 hours and cars off for 72 hours. Cooler temperatures will slow down cure time. Clean up with solvents like: xylene, toluene or lacquer thinner.
TECHNICAL DATA:
- Form: clear liquid
- Specific Gravity: 1.01
- Weight/gallon: 7.5 lbs (3.4 kg)
- Cured Coating: Resists temperatures as high as 160 degrees F (71 degrees C)
- Cured Coating: Resists temperatures as low as minus 50 degrees F ( -45 degrees C)
Limitations: Do not apply product to a damp surface. For exterior applications only. Always do a small test to ensure desired look and performance of the sealer. Do not use on retaining walls, vertical walls , polished stone or clay pavers. The solvents in the sealer will attack plastics, asphalt or petroleum based products. The minimum application temperature is 45 degrees F for the previous 20 hours. The maximum surface temperature during application is 90 degree F. In hot weather the product dries quickly so it is recommended that the product be applied in the cooler morning hours. Surface may darken during application depending upon porosity of the surface and amount of sealer applied.
Shelf Life: Two years in unopened containers. Keep tightly sealed in a ventilated area.
Coverage: Concrete pavers: 100-200 sq ft /gal, Concrete & stamped concrete: 175-250 sq ft /gal, Exposed aggregate: 100 sq ft/gallon. Coverage rate will depend on porosity and texture of the surface.
Clean Up: Clean up with solvents like: xylene, toluene or mineral spirits.
Packaging: One gallon units (4/case), five gallon pails and 55 gallon drums
Cure Time: Product will dry to the touch in typically 45-60 minutes at 74 degrees F. Keep foot traffic off for 4-6 hours and cars off for 72 hours. Cooler temperatures will slow down cure time and hot temperatures will speed up cure time.
Warning: Flammable Mixture. Keep away from flame and heat. Do not smoke. Provide adequate ventilation or if ventilation is poor, refer to SDS for further information. Avoid breathing of vapors. Skin contact may cause irritation or redness. Remove clothing if contaminated and wash skin thoroughly with soap and water. For eye contact, flush with water for 15 minutes and call a physician. If eye irritation, headaches or dizziness occurs, leave area. Do not take internally. Use safety glasses and wear chemical resistant gloves.Surfaces may be slippery when wet depending upon the amount of sealer applied to the surface. On smooth surfaces, add a non-skid paint additive to the second coat of TAMTECHseal Wet Look. See SDS for complete information. For Industrial Use Only. Keep Out Of Reach Of Children.
Reviews
There are no reviews yet.